LABEL name does not appear in LABEL instruction. Parameter is referenced in nonfunctional module, but is nowhere defined.Īn example is COND LBL,X where X is not a variable parameter in a module PARAMETER NAMED %3 HAS AN INCONSISTENT USER AUTHORIZATION The contents of /XDPL/ do not match contents of Pool Tape. *** SYSTEM FATAL/WARNING MESSAGE 24 (XGPIDG)ĬANNOT FIND DATA BLOCK NAMED %1 ON DATA POOL TAPE Note that RF24D41 requires a DTIIN command.ĭATA BLOCK NAMED %3 MUST BE DEFINED PRIOR TO THIS INSTRUCTIONĭATA BLOCK NAMED %3 IS NOT REFERENCED IN SUBSEQUENT FUNCTIONAL MODULE USER ACTION: CHECK FOR CORRECT SPELLING, OR MISSING TYPE STATEMENT, AND RERUN.Ī common mistake is to forget that DMAP statements DMIIN and DTIINĪre required to read DMI and DTI matrices, respectively. LABEL named appears in more than one place in DMAP program.ĮXTRANEOUS 'ELSE' / 'ELSEIF' STATEMENT AT INSTRUCTION %1ĭATABLOCK NAMED %1 MUST BE DEFINED PRIOR TO THIS INSTRUCTION *** USER FATAL/WARNING MESSAGE 19 (XGPIDG)
Xsort software commands manual#
Statement to the description in the NX NASTRAN DMAP Moduleĭictionary or the NX NASTRAN Programmer's Manual to find the error.
Incorrect calling sequence for DMAP instruction. TOO MANY PARAMETERS IN DMAP PARAMETER LIST *** USER/SYSTEM FATAL/WARNING/INFORMATION MESSAGE 17 (EVLMSG)
Usually caused by early termination such as a LABEL statement See the NX NASTRAN DMAP Module Dictionary. This parameter was used in a previous DMAP instruction which INCONSISTENT LENGTH USED FOR PARAMETER NAMED %3 In other cases, it may be necessary to divide the DMAP The usual cause is insufficient open core. See XGPI module description in MFD section of NX NASTRAN The named DMAP refers to a non-existent module name. *** USER FATAL/WARNING MESSAGE 13 (XGPIDG) Special characters are not allowed.įor example DMAP names like "8MOD" or "SETI=2" are not allowed. The name of a module must be alpha-numeric characters, the firstĬharacter being alphabetic. %1, ILLEGAL CHARACTER IN DMAP INSTRUCTION NAME. *** USER FATAL/WARNING MESSAGE 12 (XGPIDG)ĮRROR IN DMAP INSTRUCTION NO. Too many or too few inputs are specified in the input for the Have a value assigned before the execution of the module. Here is a parameter in the referenced DMAP instruction which must The constant needs value in a DMAP instruction or on a PARAM entry. User cannot set the value of the parameter with name %1 on a PARAM In DMAP, when defining a parameter, the "N" in V,N %1 means In DMAP, the "N" in V,N %1 or in TYPE PARM,A,B,N means userĬannot set the value of the parameter with name %1 on a PARAM entry. *** USER FATAL/WARNING MESSAGE 8 (XGPIDG)īULK DATA PARAM CARD ERROR - MUST NOT DEFINE PARAMETER NAMED %1. POSSIBLE ERROR IN DMAP INSTRUCTION %1 INSTRUCTION NO.%2 Nastran Dmap Error Message List 0-999ĮRROR IN DMAP INSTRUCTION %1 INSTRUCTION NO.%2
Xsort software commands manuals#
You should refer to your operating system manuals for interpretation of these messages. The format of these messages will vary with the operating system. Operating system specific messages can appear in the NX Nastran output. These messages will appear at the end of the output.
Warning and information messages appear at various places in the output.įatal messages will cause the program to terminate. Refer to the NX Nastran Quick Reference Guide for proper input file formats. Corrective action is often indicated in the message text. User messages typically indicate problems with the input file.
Xsort software commands full#
When 319=1, the full messages are reported. When 319=0, only message summaries are reported. The amount of information reported in a message is controlled by system cell 319. NX Nastran displays User Information, Warning, and Error messages in the printed output. Nastran Dmap Error Message List Overview of Error Messages
0 kommentar(er)
